网站首页公司概况 企业荣誉 产品简介 应用行业 科技研发 工程案例 销售网络 联系我们 在线留言
公司简介
发展历史
公司战略
企业文化
全称:河南长兴建设集团材料有限公司
联系人:杨经理
手机:0393-3558666
电话:0393-3323666
地址:河南濮阳市赵村工业园
     首页 >> 产品简介
CX-13:无溶剂环氧重防腐涂料
发布时间:2015/6/24 16:40:29 []人次

 

CX-13:无溶剂环氧重防腐涂料
成分性能:由环氧树脂、防腐颜填料、助剂、固化剂等组成,是一种双组份无溶剂型环氧防腐涂料。
产品特点:具有附着力强、柔韧性好以及耐阴极剥离性能优异等优点。
适用范围:用于恶劣环境下埋地管线内外壁、海洋工程、船舶、油罐、煤气罐、桥梁、铁塔、石油管道、混凝土、木质及非金属构件的防腐及保护设施钢结构表面中防腐。
施工说明:单组份施涂:涂料外观呈浅棕色,透明液体状
双组份施涂:漆:色浆=4:1    熟化时间:(25℃)20分钟
施工方法:高压无气喷涂、手工刷涂、轴涂
稀释剂:X-A释剂     最大稀释量:单组份不需加稀释剂,双组份≤3%
涂装间隔:单组份:最短4小时,最长72小时;双组份:最短2小时,最长24小时
表面处理:有氧化皮钢材表面需经抛丸或喷砂处理达瑞典除锈标准Sa2.5级。无氧化皮钢材表面用电动工具打磨处理达瑞典除锈标准St3级。对有底漆的表面清除前道漆面的油脂、灰尘等附着物,待其干燥后再行施涂。
配套涂料:环氧铁红底漆、环氧富锌底漆、环氧云铁中间漆等。
注意事项:
1、施工时必须计划用料、随用随配。漆料按比例混合,充分搅拌后静置20分钟后再施涂,余料不能倒回原桶。
2、施工所用容器、工具应清洁干燥,漆内不得混入水分及其他杂质。漆料现配现用,须6小时内用完。
3、施工现场应注意通风,雨、雪、雾天不宜户外施工。漆膜未完全固化之前,应避免受雨天和其他液体冲淋。
4、涂料应存放于阴凉、通风、干燥处,并隔绝火种。
  

Composition: epoxy resin, anti-corrosion pigment, additives, curing agent, etc., is a two-component non solvent type epoxy anti-corrosion coating.

Product features: with strong adhesion, good flexibility and excellent resistance to cathodic stripping performance, etc..

Scope of application: used in harsh environment internal and external walls of the buried pipeline, marine engineering, ships, tanks, gas tanks, bridges, towers, oil pipeline, concrete, wood and metal components of the corrosion and protection facilities steel structure surface anti-corrosion.

The construction instructions: one application: the appearance of coating is light brown, transparent liquid

Two-component coating: paint color: =4:1 curing time: 20 minutes (25 C)

Construction method: high pressure no gas spraying, hand painted, axis

Thinner: X-A release maximum dilution: one without diluent, two component is less than or equal to 3%

Coating interval: one: the shortest 4 hours, the longest 72 hours; two components: a minimum of 2 hours, the longest 24 hours

Surface treatment: steel surface oxide skin by blasting or sandblasting derusting of Swedish standard Sa2.5 level. Nonscale steel surface polishing treatment of Sweden derusting standard St3 grade electric tools. The attachment of the surface to remove the front paint a primer of grease, dust and so on, let it dry before applying for.

Paint: iron red epoxy primer, epoxy primer, epoxy micaceous iron oxide intermediate etc..

Note:

1, construction must be planned with the use of materials, with the use of. Paint mixing, fully stirring for 20 minutes and then applied, more than expected not back to the original bucket.

2, the construction of containers, tools should be clean and dry, paint can not be mixed with water and other impurities. Paint material is used, must be used within 6 hours.

3, the construction site should pay attention to ventilation, rain, snow, fog days not outdoor construction. The film is not completely cured, should be avoided by rain and other liquid shower.

4, paint should be stored in a cool, ventilated, dry place, and cut off the fire.

下一个:CX-12:耐高温防腐涂料
上一个:CX-30:无机硅酸锌防腐涂料
页面功能【打印】【关闭