网站首页公司概况 企业荣誉 产品简介 应用行业 科技研发 工程案例 销售网络 联系我们 在线留言
公司简介
发展历史
公司战略
企业文化
全称:河南长兴建设集团材料有限公司
联系人:杨经理
手机:0393-3558666
电话:0393-3323666
地址:河南濮阳市赵村工业园
     首页 >> 产品简介
CX-03丙烯酸聚氨酯防腐涂料
发布时间:2015/6/23 18:26:31 []人次

 

CX-03:丙烯酸聚氨酯防腐涂料

成分性能:改性丙烯酸环氧和聚氨酯树脂为基料,加入无毒颜填料、助剂等组成。

产品特点:漆膜无毒、附着力强、干燥快、施工方便,并具有良好的耐酸、碱、盐腐蚀性能,耐水、耐油、耐候性优良。
适用范围:管道的内外壁、金属、混凝土水池、水箱的内外壁防腐涂装。用于煤气罐、输气、储油罐及输油管管件的内、外壁防腐涂装。用于环保设备、船舶、桥 梁、铁塔、污水处理工程及其 他钢结构、混凝土结构的地下或地面的防腐工程的涂装。
施工说明:混合配比:底漆::手工刷涂、轴涂       稀释剂:X-A稀释剂      最大稀释量:≤5%   
涂装间隔:(25℃)最短1小时,最长48小时
表面处理:清除被涂物表面的氧化皮、焊渣、油污、浮尘等,达到瑞典除锈标准St2级。如前道漆面已污染,应除去油脂、灰尘,待其干燥后再行施工。
配套涂料:CX面漆、环氧面漆、丙烯酸面漆等。     配套底漆:CX底漆等。
注意事项:
1、施工时必须计划用料,随用随配。漆料按比例混合,充分搅匀后静置20分钟后施涂,涂料不能倒回原桶。
2、施工所用容器、工具应清洁干燥,漆内不得混入水分及其他杂质。
3、必须待前道漆表面干后方可施涂下道漆。
4、缠绕玻璃纤维布必须平整张紧、网眼灌满涂料。
5、管道口处应注意清除泥土、水迹。回填土时应注意避免损伤防腐层。
6、涂层未完全固化前不得进行埋管施工,涂装后的防腐件在运输、吊装过程中应避免损伤,如有损伤应及时修补。
7、施工现场应注意通风,雨、雪、雾天不宜户外施工。
8、涂料应存放于阴凉、通风、干燥处,并隔绝火种。
 
Composition: modified acrylic epoxy and polyurethane resin as the base material, adding non-toxic pigment, fillers, additives, etc..
Product features: film non-toxic, strong adhesion, fast drying, construction is convenient, and has a good acid, alkali, salt corrosion performance, water resistance, oil resistance, weathering resistance.
Applicable scope: the inside and outside wall of the pipeline, metal, concrete pool, water tank of the internal and external wall coating. Used in gas tank, gas transmission, storage tank and oil pipe fittings of internal and external wall coating. Used in environmental protection equipment, ship, bridge beam, tower, sewage treatment works and his steel structure, concrete structure of the underground or the surface of the anti-corrosion coating.
Construction Description: mixing: Primer:: manual brushing, shaft coated diluent: X A. diluent maximum dilution of less than or equal to 5%
Coating interval: (25) the shortest 1 hours, the longest 48 hours
Surface treatment: remove the coated oxide on the surface of the skin, welding slag, oil, dust, rust to Swedish standard St2 level. As before the paint contaminated, should remove grease, dust, to dry after construction.
Paint: CX paint, epoxy paint, acrylic paint etc.. Matching primer: CX primer, etc..
Note:
1, construction must be planned with the use of materials, with the use of. Paint mixing, stirring after standing for 20 minutes after the application, not back to the original paint bucket.
2, the construction of containers, tools should be clean and dry, paint can not be mixed with water and other impurities.
3, must be before the road paint surface can be applied to paint the next.
4, winding glass fiber cloth, mesh tension must be flat filled with paint.
5, the pipe mouth should pay attention to remove dirt, water mark. To avoid damage and corrosion protection layer should be paid attention to.
6, the coating is not completely cured before the construction of the buried pipe is not allowed, the anti-corrosion coating in the transport, lifting process should avoid damage, such as damage should be repaired in time.
7, the construction site should pay attention to ventilation, rain, snow, fog days not outdoor construction.
8, paint should be stored in a cool, ventilated, dry place, and cut off the fire.


 

下一个:CX-02氯磺化聚乙烯防腐涂料
上一个:CX-30:无机硅酸锌防腐涂料
页面功能【打印】【关闭